DCC Decoders

The Decoder Buddy V5 and V5B were developed for the 12 output decoders and include a couple added features. This mother board does not include the 21-Pin Decoder. This mother board requires soldering. This printed circuit board is NOT INTENDED FOR USE IN...

Dimensions: 0.595" x 0.390" (15mm x 10mm)  Direct plug in to locos equipped with Next18 (NEM-662) socket  Features of this decoder: Silent Running(TM) Torque compensated motor drive Torque Compensation for ultra smooth low speed...

N Scale N14K2 Drop-In Control Only Decoder. Includes pre-soldered motor clips.

Drop in decoder for Kato N scale. Includes pre-soldered motor clips. Works for: Athearn EMD F45 Athearn EMD FP45  Kato "Gevo" ES44AC  Kato AC4400  Kato C30-7  Kato GE C44-9W Kato SD40-2 early versions Kato ES44  ...

Plug in 4 function decoder with 6 pin NEM 651 connector Dimensions: 2.65 X 8.77 mm Includes pins 19.41 mm

This HO sized decoder is designed for use in HO Locomotives: Kato RS2/RSC2 and C44-9 Stewart VO-1000 Intermountain F7 Atlas U23B and U30B The easiest installation possible, just plug it in! 1.3 Amp rating (2 Amp peak). Six function outputs and...

 The LokSound 5 micro is a “little wonder”: With only 21mmx10mm footprint, it is by far one of the smallest LokSound decoders we’ve ever built. Thus it should fit into all N gauge and TT vehicles, but is also suitable for small H0 vehicles. All...

With its unique design the LokSound 5 Direct DCC can easily replaceboards that provide poor motor control, low volume, or generally inferiorsound. Not only will the decoder work fine with most factory installedspeakers, but it will sound even better with...

  LokSound 5 micro DCC "blank decoder", 8-pin NEM652, gauge: N, TT, H0   The LokSound 5 micro is a “little wonder”: With only 21mmx10mm footprint, it is by far one of the smallest LokSound decoders we’ve ever built. Thus it should fit...

 The LokSound 5 micro DCC Direct has been specially developed for installation in Spur N vehicles of the Atlas and Intermountain brands: it can be inserted directly instead of the analog board installed there as standard. However, the decoder can...

 The LokSound 5 is the most important member of the LokSound family. Due to the combination of the digital decoder and the sound module on one circuit board we achieve the smallest possible dimensions of 30 mm x 15.5 mm. Therefore it fits into...

 The LokSound 5 is the most important member of the LokSound family. Due to the combination of the digital decoder and the sound module on one circuit board we achieve the smallest possible dimensions of 30 mm x 15.5 mm. Therefore it fits into...

Decoder tester (Replaces 51900), NEM651, NEM652, 21MTC, PluX22, Next18, single wires. With motor, LED-Monitor and 20mm speaker. New socket to accept decoder tester extension 53901Â Perhaps you are familiar with this scenario: there is a digital decoder...

LokProgrammer set: LokProgrammer unit, US 110V power supply, and serial to USB PC cable Dimensions: 95mm (3.74") x 85mm (3.35") x 22mm (0.87")   You want to listen to the sound spectrum of your favourite loco, or the special sound of that loco...

The ESU SignalPilot decoder is a multi-protocol decoder designed primarily for switching daylight signals. It has 16 outputs to which micro lamps or LEDs (with series resistors) can be connected directly. Because all outputs are designed as push/pull...

If required, SwitchPilot can be augmented with the SwitchPilot Extension Modul: Plugged in at the side of the SwitchPilot, it offers four relay-driven outputs, used for switching potential-free loads, or for polarizing the frog; the ideal supplement for...

Board replacement SoundFX®/motor/FX3 function decoder for N Scale Atlas SD50/60 diesels Board replacement decoder for N Scale Atlas SD50/60 diesels Preloaded with our SD50/60 sound scheme 4 FX3 Functions Visit Digitrax Sound Depot...

Board replacement SoundFX®/motor/FX3 function decoder for N Scale Atlas GP38 diesels Board replacement decoder for N Scale Atlas GP38 diesels Preloaded with our GP38 sound scheme 4 FX3 Functions Visit Digitrax Sound Depot to learn...

Fits Many DCC-Ready Z, N and HO Scale Locomotives Size: .55” x .4” x .148”14mm x 10.23mm x 3.77mm Z/N/HO Scale 1.0 Amp/1.5 Amps Peak 4 FX3 Functions, 0.5 Amp DCC Medium Plug with 1 ‘...