- Product
- Qty in Cart
- Quantity
- Price
- Subtotal
-
Accu Lites 10006 - SNAPS! II Wiring Connector for Tortoise Switch Machine -- 2020 Update with Wider Connection, 12 Volt (6 PACK) - Multi Scale
$35.65Note: designed for use with Tortoise(TM) switch machines manufactured after May/June 2020. See ACL1001 for old version SNAPS! is a new product that we have developed and manufactured in-house here at ACCU-LITES, Inc. SNAPS! is a EZ wiring connector for... -
ESU 51831 - SwitchPilot 3 Plus: 8x Accessory Decoder - Multi Scale
$71.39SwitchPilot 3 Plus decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary consumption. In order to facilitate the rather... -
2 foot RJ12-6P6C (DCC cable)
$4.95RJ12 cable with a length of 2 feet. For use with DCC systems such as Digitrax LocoNet. -
Kato 22-102 - Analog Sound Box - Multi Scale
$306.18In-Cab Sound from the comfort of your home The Analog Sound Box has been developed as a joint effort between engineers at Kato and Soundtraxx to craft a simple, versatile, and powerful sound system for use on non-DCC layouts. Completely... -
Accu Lites 10001 - SNAPS! II Wiring Connector for Tortoise Switch Machine -- 2020 Update with Wider Connection, 12 Volt - Multi Scale
$6.81Note: designed for use with Tortoise(TM) switch machines manufactured after May/June 2020. See ACL1001 for old version SNAPS! is a new product that we have developed and manufactured in-house here at ACCU-LITES, Inc. SNAPS! is a EZ wiring connector... -
Accu Lites 10000 - Updated Tortoise Card Edge Connector II for 2020 Update Tortoise with Wider Connection, 12 Volt
$3.68Tortoise Card Edge Connector Our Edge Connector Now without shims redesigned for a SNUG fit for the updated tortoise switch machine. The newer tortoises have a green edge connector. See images. See ACL1000 to fit older switch machine -
Digitrax UP7 - LocoNet Universal Panel - Multi Scale
$16.96Plug and Play Universal fascia panel supporting LocoNet. Two RJ12 front panel Throttle jacks. Three RJ12 rear pass-through LocoNet jacks Supports throttle charging. Fully connectorized installation. 2mm rear plug for e.g. PS14 DC power supply. 4-pin... -
Digitrax PM74 - Power Manager with Occupancy and Transponding detection for 4 sub-districts - Multi Scale
$88.944 Power Manager sub-districts. Upgraded replacement for PM42, fully encased. Fully connectorized installation. Each Power sub-district / Detection Section (DS) supports Auto-reverse or Short circuit management. Each DS supports Occupancy detection. Each... -
RR-CirKits, Inc SPL-62 - Multiple Terminal Block, Push-in Wiring Cable Connector 2 in, 6 out - Multi Scale
$1.22Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 6 out. No more soldering under the layout. Fits AWG 28 - AWG 12 so there is no problem connecting different wire sizes together. Easily disconnect wiring for trouble... -
RR-CirKits, Inc 3TK2-1 - Single Position Mounting Track - Multi Scale
$2.77This plastic mounting track is suitable for mounting a single I/O module to a flat surface. (3 1/2" x 2") -
RR-CirKits, Inc CT-coil-set-4 - Coils, current sensing, set of 4 - Multi Scale
$7.49Set of 4 CT (Current Transformer) coils for BOD4 or BOD4-CP. -
RR-CirKits, Inc CT-coil-set-8 - Coils, current sensing, set of 8 - Multi Scale
$14.50Set of 8 CT (Current Transformer) coils for BOD-8. These 100:1 toroid coils sense the track current on leads passing through the hole in the middle of the coil. They connect to the BOD-8 with twisted pair cable such as CAT-3 or CAT-5 network cable. (up... -
RR-CirKits, Inc BOD-4 - 4 Block DCC Occupancy Detector, DCC Only, Rev D - Multi Scale
$20.55(Block Occupancy Detector-4) This board operates as a DCC occupancy detector for 4 blocks using remote CT coils. It outputs logic levels, and has a RR-CirKits standard ribbon connector interface. The "Power-Lok" feature optionally monitors the DCC bus... -
RR-CirKits, Inc BOD-8-SM - 8 Block DCC Occupancy Detector, DCC Only, Sample Mode compatible - Multi Scale
$38.54(Block Occupancy Detector-8 - SM) This new board is compatible with LCC node sample mode which allows using output drivers on the same I/O port. This board operates as a DCC occupancy detector for 8 blocks using remote CT coils. It outputs logic levels,... -
RR-CirKits, Inc Signal-LCC-P - Signal LCC Board with IDC Pin connections - Multi Scale
$59.9016 Led drivers plus 8 line Input/Output node for NMRA CAN bus LCC®. Logic level I/O port compatible with other standard RR-CirKits I/O modules. Boot Loader for user installable firmware upgrades. Includes powerful internal Logic Elements. Compatible with... -
RR-CirKits, Inc Signal-LCC-S - Signal LCC Board with screw terminal connections - Multi Scale
$59.9016 Led drivers plus 8 line Input/Output node for NMRA CAN bus LCC®. Logic level I/O port compatible with other standard RR-CirKits I/O modules. Boot Loader for user installable firmware upgrades. Includes powerful internal Logic Elements. Compatible with... -
Digitrax DS78V - Eight Servo LocoNet Stationary & Accessory decoder for turnout control
$69.36Eight 9G servo decoder for 2-position Slow-motion turnouts. Configurable to control eight 3-position semaphores. Works with compatible LocoNet Systems. Plug and play connections. Option setup switches for configuration. On-layout... -
Atlas 200 - Snap-Relay - Multi Scale
$16.73A double-pole, double-throw relay with actuating mechanism driven by a momentary-power, twin coil solenoid. (A solenoid is a cylindrical coil of insulated wire in which an iron core is made to move back and forth by a flow of electric current.) With just... -
Train Control Systems (TCS) 1454 - KA 1 (Keep Alive) - Multi Scale
$27.03TCS Keep-Alive® (KA) devices are used to supply power to decoders during times of power interruption due to dirty track or problematic track work. Newly-redesigned and coming in at half the size of a KA3, the KA1 will power HO or N scale locomotives... -